IEEE 386 Cable Accessories 15kV-35kV 200A LoadBreak Elbow Connector for Pad Mounted Transformer

IEEE 386 Cable Accessories 15kV-35kV 200A LoadBreak Elbow Connector for Pad Mounted Transformer - 图片 2

IEEE 386 Cable Accessories 15kV-35kV 200A LoadBreak Elbow Connector for Pad Mounted Transformer

The loadbreak elbow is a fully shielded and insulated termination connecting underground cable to transformers,switchgear,and other apparatus equipped with loadbreak bushings,junctions,or other loadbreak connectors. It meets allthe requirements of IEEE Standard 386(small interface,meet figure 7B in IEEE Std 386-2016).
The loadbreak elbow is molded using high quality peroxide-cured insulating and semi-conducting EPDM rubber,itinclude a stainless steel pulling eye. An optional capacitive test poin…

Category: Pad-mounted Transformer and Accessories

SKU: I3CA1-165

Description
Additional information

Description

The loadbreak elbow is molded using high quality peroxide-cured insulating and semi-conducting EPDM rubber,itinclude a stainless steel pulling eye. An optional capacitive test point is available.Included with the elbow kit is a bi-metalor copper compression connector, and a tin plated copper probe with an arc quenching tip.

Rated Voltage(Phase-to-Phase)	15kV	25kV	35kV
Withstand Voltage(50/60Hz)	34kV/1min.	34kV/1min.	50kV/1min.
BIL and Full Wave Crest	95kV	125kV	150kV
Minimum Corona Voltage Level	11kV	19kV	26kV
Continuous Current	200A	200A	200A

xq_09

xq_11

Read more

15-35kV 200-600A Loadbreak Insulation Protective Cap for Cable Connector Insulation

This Insulation Protective Cap is an accessory product to other 15kV 200A products with loadbreak interfaces (bushing inserts, loadbreak junctions, feed thru inserts, etc.).It is designed to physically seal and electrically insulate loadbreak bushing interfaces. When installed on a loadbreak bushing interface, and properly grounded using the attached drain wire, the Loadbreak Insulation Protective Cap provides a submersible, fully shielded insulated cap for energized bushings. The Loadbreak Insu…
Read more

35kv 630A Gas Insulated Loadbreak Bushing Well Insert

This plug-in bushing can be used as a fixed section for the entry of medium voltage on switch gears or transformers.
Indoors for vertical or horizontal mounting; outdoors both with and without tension making use of the fitting rubber connector, for vertical or horizontal mounting.
Product name
Rated voltag
Rated current
TGSF6-35/1250-C/F
15KV
630A
QTTG-35/2500-F
15KV
630A
Read more

24kv 250A Loadbreak Elbow Connector

24kV/250A elbow cable connector can be installed horizontally and reduce the bending radius of current.Applicable cable section is between 35 mm
2
to 150mm
2
.
product structure：
Stud bolt
Inner and Outer Semiconducting Layer
Insulating layer
Voltage test point
Crimping terminal
Grounding point
Stress cone
order number
Cable cross-sectional area/mm
2
Conductor diameter/mm
Cable insulation outer diameter/mm
NRZT-15/200-35
35
7.0-7.5
17.0-19.0
NRZT-15/200-50
50
8.0-8.5
18.0-20.0
NRZT-15/200-70
70…
Read more

15-35kV 200A Epoxy Resin Loadbreak Bushing Insert for Pad-mounted Transformers with Extreme Climate Resistance

The Bushing Insert threads onto a standard 200A bushing well.The combination of the bushing well and bushing insert perform the same function as a one piece integral loadbreak bushing, while providing the flexibility to change the bushing insert in the field, without taking the transformer or other apparatus out of service. The bushing insert and loadbreak elbows are the primary components in all ANSI/IEEE loadbreak connections.
The Bushing Insert incorporates an all copper current path.This pro…